GOEPEL electronic

Address:
Goeschwitzer Str. 58/60
Jena
07745
Germany

Phone: +49-3641-68960

Fax: +49-3641-6896944

Web: www.goepel.com


GOEPEL electronic articles

Displaying 1 - 20 of 37

Test solutions extended to support Intel Arria 10 SoC

Test solutions extended to support Intel Arria 10 SoC
The embedded board test technologies ChipVORX and VarioTAP from GOEPEL electronic now support the Intel Arria 10 SoC (System-on-Chip). The new IP models simplify testing and programming of the devices.
9th September 2018

Module measures and tests analogue voltages on 128 channels.

Module measures and tests analogue voltages on 128 channels.
The SFX/VPC-AMC128 (Analog Measurement Card) is a new test extension module. It can be used to measure and test analogue voltages on 128 channels. The module can be easily integrated into the in-line test system RAPIDO from GOEPEL electronic, as well as into customer-specific test systems.
1st June 2018

Software option protects FPGA designs

Software option protects FPGA designs
A Security Key Programming software option that allows programming of a 256-bit AES key for Altera Cyclone V FPGAs has been released by Goepel electronic. It activates the design security in the FPGA, thus bitstreams can no longer be analysed. This protects the FPGA design against re-engineering, cloning and copying.
11th April 2018


Boundary scan test extended to PSoC 4 controllers

Boundary scan test extended to PSoC 4 controllers
The VarioTAP model range has been extended by Goepel to include Cypress PSoC 4 controllers. The VarioTAP model libraries allow a complete fusion of Boundary Scan test and JTAG emulation. The processor is controlled via the native debug port, allowing users to perform hardware design validation and prototype testing without firmware.
9th January 2018

productronica 2017: Detector aids X-ray inspection

productronica 2017: Detector aids X-ray inspection
StingRay Detector is the name of the new image acquisition concept for fully automatic X-ray inspection of single-sided and double-sided PCBs from Goepel electronic. It enables selective 2D, 2.5D and 3D X-ray inspection with high image quality at highest speed. The StingRay Detector is another option for the inline AXI systems of the X Line · 3D family. It will be on show at productronica in Munich (November 14-17).
6th November 2017

productronica 2017: X-ray detector to feature

productronica 2017: X-ray detector to feature
At productronica in Munich (November 14-17), GOEPEL electronic will present fully automated inspection solutions, offering high fault detection, flexibility and cost reductions through time savings. Being highlighted is the new StingRay X-ray detector, an additional option for the system family X Line · 3D.
13th October 2017

Interface card supports JTAG/Boundary Scan protocols

Interface card supports JTAG/Boundary Scan protocols
With the TIC022-MUX/SR, GOEPEL electronic is presenting an external TAP interface card (TIC) for operation with the Embedded JTAG Solutions platform SCANFLEX. The module serves as the interface for performing various test and programming procedures and can also be integrated into other test systems, such as In-Circuit testers and flying probers.
6th October 2017

Communication controller is compatible with Linux

Communication controller is compatible with Linux
The Series 61 communication controller portfolio for CAN/CAN-FD, FlexRay, K-Line and LIN has been extended to be compatible with Linux by GOEPEL electronic. The interface has been ported; function names and parameters remain unchanged, so users can easily develop platform-independent software. The G-API (GOEPEL electronic Application Programming Interface) previously only supported Windows-based systems.
18th September 2017

X-ray inspection systems fit the bill for automotive supplier

X-ray inspection systems fit the bill for automotive supplier
The Italian automotive supplier Magneti Marelli has chosen two X-ray inspection systems from GOEPEL electronic for its quality assurance of electronic assemblies. At production sites in France and Slovakia, the X Line · 3D systems are used to inspect high-complexity PCBs. Electronic assemblies for automobiles are subject to particularly high quality requirements by the manufacturers.
14th August 2017

JTAG/Boundary scan controller uses embedded instruments

JTAG/Boundary scan controller uses embedded instruments
SCANFLEX II CUBE is the latest generation of modular JTAG/Boundary Scan controllers developed by GOEPEL electronic.. Based on the latest multi-core processors and FPGAs, SCANFLEX II CUBE opens new ways for the Embedded JTAG Solutions. This test and validation method uses embedded instruments to test and program complex boards.
12th June 2017

Embedded JTAG to debut at Embedded World 2017

Embedded JTAG to debut at Embedded World 2017
State-of-the-art test technologies, powerful test bus simulation for vehicle networks and a broad array of test technologies will all be paraded at Embedded World 2017 (March 14-16) by GOEPEL electronic.
1st March 2017

Software test program supports ARM-based processor

The Embedded Test and Diagnostics Operating System JEDOS is now available for processors of the i.MX6 family from NXP. With this, functional circuit tests can be performed in real time using the native processor. The use of special test software or firmware is completely omitted.
5th December 2016

Improved production throughput in SPEA Flying Probe Systems

Improved production throughput in SPEA Flying Probe Systems
The boundary scan integration in the flying prober 4060 from SPEA is being expanded to the ability of panel test. Thus, panels with several boards can now be tested and also use the whole performance of the interactive test. The combined test of flying probe and boundary scan tests every board and collects all results in a joint protocol. This allows an ideal use of the flying probe resources within the boundary scan tests and offers as a consequence enhanced test depth and test coverage.
28th September 2016

Processor emulation tools extended for Bluetooth SoC controller

The range of processor emulation tools from GOEPEL electronic has been extended for the Nordic Semiconductor nRF52 series, thus enabling the processor to be reconfigured to provide design-integrated test and programming instruments via the SWD port. A respective VarioTAP model, as part of an extensive IP library, contains all relevant access information for the target processor.
5th September 2016

Model libraries extend FPGA test functions

Model libraries extend FPGA test functions
The availability of ChipVORX model libraries for Bit Error Rate Test (BERT) using SoC FPGAs of the Altera Arria V series to support embedded test and embedded programming has been extended by Goepel electronic. ChipVORX is a technology for universal control of Chip Embedded Instruments via JTAG port.
25th August 2016

AOI system minimises test footprint

Completely frictionless and maintenance-free with minimised footprint and unsurpassed inspection speed, GOEPEL electronic has unveiled MultiCam Line, its newest inline AOI system. Based on the unique multi-camera image acquisition module MultiEyeS, it provides placement inspection of THT components with a test speed of up to 300 cm²/s.
24th August 2016

Compact frictionless AOI inline system

Compact frictionless AOI inline system
GOEPEL electronic has launched MultiCam Line, an inline AOI system. Based on the  multi-camera image acquisition module MultiEyeS, it provides placement inspection of THT components with a test speed of up to 300 cm²/s. The camera module consists of multiple cameras arranged in a matrix-like configuration with a combined resolution of 120 megapixels. 
24th August 2016

IPC compliant THT solder joint inspection

IPC compliant THT solder joint inspection
The X-ray inspection system X Line 3·D from GOEPEL electronic is designed to enable reliable inspection of THT and Pin-in-Paste solder joints in compliance with the IPC quality standard through a unique combination of 3D X-ray (AXI) and 2D AOI inspection. This level of inspection is particularly important for automotive assemblies which are subject to strict quality requirements.
23rd June 2016

Distribution deal takes test products to China

Distribution deal takes test products to China
GOEPEL electronic has entered into close partnership with the Chinese technology company Pansino Solutions for distribution of automotive test products. This cooperation will meet the growing demand for test systems, diagnostic tools for automotive ECUs and simulation systems for electrical vehicle components in the Chinese area.
17th May 2016

Mixed-signal test generator accelerates designs

Mixed-signal test generator accelerates designs
A new software tool from GÖPEL electronic allows test programs to be automatically generated from analogue/digital designs. The mixed-signal test generator automates test sequences which until now have been generated manually, dramatically reducing the overall conditioning and parametrisation work involved. As a result, project creation is safer, more effective and more flexible.  
3rd May 2016


Sign up to view our publications

Sign up

Sign up to view our downloads

Sign up

SPS IPC Drives 2018
27th November 2018
Germany Nuremberg
International Security Expo 2018
28th November 2018
United Kingdom London Olympia
The Security Event 2019
9th April 2019
United Kingdom NEC, Birmingham
Ceramics Expo 2019
29th April 2019
United States of America International Exposition Center (I-X Center)