The inline X-ray system X Line · 3D Series 400 from Goepel has a new detector option for high-resolution 3D X-ray inspection of electronic assemblies. The MultiAngle Detector 3 combines the high image quality of the StingRay Detector introduced last year with the rapid inspection speed of a scanning image.

Automotive Ethernet is a standardised interface in the automotive industry and an important component of future vehicle architectures. GOEPEL electronic has now developed the second generation of the EasyCON media converter. It physically converts a standard Ethernet layer to Automotive Ethernet 1000/100 Base-T1.

Test and inspection solutions for electronics development and production will be showcased by Goepel at electronica 2018 in Munich (November 13-16). Centre stage is ChipVORX-SI, a future-oriented platform using powerful FPGA-IP for test & in-system programming.

The embedded board test technologies ChipVORX and VarioTAP from GOEPEL electronic now support the Intel Arria 10 SoC (System-on-Chip). The new IP models simplify testing and programming of the devices.

There will be a changing of the guard at GOEPEL lectronic on August 15, when Alice Göpel will take over the Managing Director position of GOEPEL electronic. She replaces her father Holger Göpel, who has been managing the company since 1991. He is retiring but will still be available to the company as a consultant.

The JTAG/Boundary Scan controller SCANFLEX II Cube from Goepel electronic now has an optional Wireless LAN interface. Previously, the controller had USB 3.0 or LAN interfaces as standard. With the new option, another control interface is now available. SCANFLEX II Cube is a modular JTAG/Boundary Scan controller.

The SFX/VPC-AMC128 (Analog Measurement Card) is a new test extension module. It can be used to measure and test analogue voltages on 128 channels. The module can be easily integrated into the in-line test system RAPIDO from GOEPEL electronic, as well as into customer-specific test systems.

A new generation of multibus communication controllers under the name “Series 62” has been announced by Goepel electronic. The architecture offers users up to 18 independent bus interfaces for CAN, CAN-FD, FlexRay, Automotive Ethernet and LIN. This results in numerous configurations and thus application options for optimum adaptation to the UUT (unit under test) or the test task.

A Security Key Programming software option that allows programming of a 256-bit AES key for Altera Cyclone V FPGAs has been released by Goepel electronic. It activates the design security in the FPGA, thus bitstreams can no longer be analysed. This protects the FPGA design against re-engineering, cloning and copying.

  With basicCON 4045, GOEPEL electronic has presented a stress module specifically for automotive Ethernet applications (BroadR-Reach). The simulation of physical faults manipulates the ECU communications, allowing conclusions to be drawn about the stability and robustness of Ethernet vehicle applications.

The VarioTAP model range has been extended by Goepel to include Cypress PSoC 4 controllers. The VarioTAP model libraries allow a complete fusion of Boundary Scan test and JTAG emulation. The processor is controlled via the native debug port, allowing users to perform hardware design validation and prototype testing without firmware.

StingRay Detector is the name of the new image acquisition concept for fully automatic X-ray inspection of single-sided and double-sided PCBs from Goepel electronic. It enables selective 2D, 2.5D and 3D X-ray inspection with high image quality at highest speed. The StingRay Detector is another option for the inline AXI systems of the X Line · 3D family. It will be on show at productronica in Munich (November 14-17).

At productronica in Munich (November 14-17), GOEPEL electronic will present fully automated inspection solutions, offering high fault detection, flexibility and cost reductions through time savings. Being highlighted is the new StingRay X-ray detector, an additional option for the system family X Line · 3D.

With the TIC022-MUX/SR, GOEPEL electronic is presenting an external TAP interface card (TIC) for operation with the Embedded JTAG Solutions platform SCANFLEX. The module serves as the interface for performing various test and programming procedures and can also be integrated into other test systems, such as In-Circuit testers and flying probers.

The Series 61 communication controller portfolio for CAN/CAN-FD, FlexRay, K-Line and LIN has been extended to be compatible with Linux by GOEPEL electronic. The interface has been ported; function names and parameters remain unchanged, so users can easily develop platform-independent software. The G-API (GOEPEL electronic Application Programming Interface) previously only supported Windows-based systems.

The Italian automotive supplier Magneti Marelli has chosen two X-ray inspection systems from GOEPEL electronic for its quality assurance of electronic assemblies. At production sites in France and Slovakia, the X Line · 3D systems are used to inspect high-complexity PCBs. Electronic assemblies for automobiles are subject to particularly high quality requirements by the manufacturers.

A special software option for the use of the VarioTAP emulation technology on Cypress USB 3.0 controllers has been developed by Goepel electronic. The EZ-USB FX3 can now be tested and programmed much more efficiently due to special model libraries. Users also benefit from cost savings for additional test and programming equipment.

SCANFLEX II CUBE is the latest generation of modular JTAG/Boundary Scan controllers developed by GOEPEL electronic.. Based on the latest multi-core processors and FPGAs, SCANFLEX II CUBE opens new ways for the Embedded JTAG Solutions. This test and validation method uses embedded instruments to test and program complex boards.

State-of-the-art test technologies, powerful test bus simulation for vehicle networks and a broad array of test technologies will all be paraded at Embedded World 2017 (March 14-16) by GOEPEL electronic.

With basicCAN6153.STM GOEPEL electronic has introduced a stress and trigger module for CAN FD. It is specifically capable of manipulating CAN / CAN FD communication enabling accurate protocol tests. The functionality is available as an extended option for the Series 61 communication controllers.